Lee Carbide Factory Pistol Crimp Die .44 Special, .44 Magnum, .44 S&W Russian

» Main Menu » ● RELOADING, Tools and Equipment »
RELOADING DIES, Die Set »
RELOADING DIES, Pistol and Revolver » .44 REMINGTON MAGNUM » 90863

| My Account | My Shopping Cart | Proceed to Checkout |

Languages

Product Search

Manufacturers

Informatie

● QUESTIONS & ANSWERS

● SHIPPING & ORDERING

● CONDITIONS of USE

Overige Info

● WET WAPENS & MUNITIE

● PRIVACY POLICY

● CONTACT US

Lee FACTORY CRIMP DIE .44 Special, .44 Magnum, .44 S&W Russian
[90863]

39.50 Euro

Lee FACTORY CRIMP DIE .44 Special, .44 Magnum, .44 S&W Russian

Product may vary slightly from image representation

Description

Factory ammunition is often more accurate and better able to withstand rough handling because the bullet is firmly crimped in place.
A firm crimp improves accuracy because pressure must build to a higher level before the bullet begins to move.
This higher start pressure insures a more uniform pressure curve and less velocity variation.
Even powder selection is less critical.

A carbide sizer in the Carbide Factory Crimp Die sizes the cartridge while it is being crimped so every round will positively chamber freely with factory like dependability.
The adjusting screw quickly and easily sets the desired amount of crimp.
It is impossible to buckle the case as with a conventional Bullet Seating Die.
Trim Length is not critical so this extra operation takes less time than it would if cases were trimmed and chamfered.

For revolver rounds a Roll Crimp is used.
A Taper Crimp is applied to auto-loader rounds.
The crimper cannot be misadjusted to make a case mouth too small to properly head-space.

A firm crimp is essential for dependable and accurate ammunition.
It eliminates the problems of poor ignition of slow burning reloading powders.

Instructions

The Lee Factory Crimp Die does not seat the bullet. The bullet should be seated with your regular bullet seating die.
If the bullet has a crimp groove it is usually best to seat the bullet so most of the groove is inside the case mouth.

● Screw the Lee Carbide Factory Crimp Die until it just touches the shell holder and back out the adjusting screw. With the loaded round in the die turn the adjusting screw in until you can feel it just touch the case mouth. Then move the cartridge out of the die slightly and screw the adjusting screw in ½ turn for a light crimp and one full turn for a heavy crimp. You can adjust for even greater crimp and never have to worry about buckling the case as with conventional crimpers.
It is usually best to start with a light crimp as you can readjust and crimp again to suit your needs.

● The case is sized as it enters the die and again as it is pulled out of the die. This assures you every case will freely chamber in any standard gun.
Do not expect the carbide sizer to touch every case. It is a fail safe tool for the occasional bad round that could ruin your day.

● Bullets do not need a crimp groove as the Lee Factory Crimp Die will form one while crimping.
However it requires a harder push on the press lever to form the crimp.

● Finger tighten the lock ring.
This locks to both the die and press and it will never move.

● When removing the die always loosen by the lock ring.
This insures the lock ring will maintain its setting for future use.

● Trim length is not critical.
However be certain that your cases are no longer than specification as a case excessively long will pinch the bullet in the end of your gun's chamber and cause dangerous pressures.
Cases trimmed excessively short cannot be crimped.

You might also like...

Lee FACTORY CRIMP DIE .223 Remington	Lee FACTORY CRIMP DIE .38 Special, .357 Magnum, .357 Remington Maximum	Hornady POWDER TRICKLER
Lee AUTO-PRIME SHELLHOLDER 4

........ShoppingCart........

1 x	Ballistol Gun Oil Spray 100 ml
1 x	Birchwood Casey Darkotic SMOKEHOUSE Splattering Target
1 x	Butler Creek FLIP-UP Scope Cover OBJECTIVE size 33, 51.9mm
1 x	Caldwell MAGNUM EXTENDED REAR BAG Shooting Bag - Filled
1 x	Crosman Pellet Loader 4.50mm
1 x	Diana MAGAZINE for Diana MAGAZINE for Airbug, Bandit, Chaser and Stormrider 7 Shot 5.50mm
1 x	Funfair Target SHOOTING HAND container of 25
1 x	Gamo Pro Hunter 5.50mm Airgun Pellets tin of 250
1 x	H&N Baracuda Magnum 4.50mm Airgun Pellets tin of 200
1 x	H&N Field Target Trophy 5mm Airgun Pellets tin of 250
1 x	H&N Heavy Slug 6.35mm .249 Airgun Pellets 2.85 gram, 44 grain tin of 100
1 x	Hatsan VORTEX GAS PISTON type 2: Model 125, 125TH, 125 Sniper, 135, Torpedo 150, 150TH, 155
1 x	Hawke FRONTIER 30 SF 4-24x50 Rifle Scope reticle Mil Pro IR
1 x	Hawke HONEYCOMB SUNSHADE Objective 40mm AO
1 x	Hornady Lock-N-Load Cartridge Gauge .40 Smith & Wesson
1 x	Lyman BLACK POWDER GOLD Bullet Lube
1 x	Lyman CASE PREP MULTI-TOOL
1 x	RCBS Chamber Cartridge Length Gauge .45 Colt
1 x	Weihrauch SILENCER 1/2 inch UNF for Air Rifle 4.50mm - 5.50mm

1,278.85 Euro

Tell a Friend

New Products

Ares LEAD ROUND BALLS .312 caliber 7.93mm box of 100
7.95 Euro

All prices are including VAT. All prices are excluding shipping.
To be of better service to you target-master makes use of cookies.

E-mail: contact form

K.v.K. Noord: 01089355.
Licence for Weapons trade: GR 20050217.

Copyright © 2005 - 2024 Target-Master. All rights reserved.